Apollo P40 Software-V3.18

Ultimea
Ultimea

Attention:

Before proceeding with the software installation, please make sure that your projector software version is: V3.09 (Settings>About>Software version>"U0320-XXX" to check the software version)

Software Function Improvement Points:

① Solve UI interface problem ( WLAN keyboard "u" and "i" capitalization)
② Optimize keystone correction function
③ Add projector HDMI ARC/HDMI CEC function (for HDMI connect the soundbar, use the projector remote to control the soundbar on/off, and volume adjustments)
④ Manual focus improves adjustment accuracy

Installation Steps:

Step 1: Please prepare a USB flash drive, the format of the USB must be FAT 32 and the capacity of the USB must be more than 4G;
Note: The USB flash drive is empty and cannot have other files.

Step 2: The installation package V3.18, please download the file from the link: 

Apollo P40 Installation Package-V3.18

Step 3: Copy the "MstarUpgrade9255BGA.bin" upgrade file to the root drive of the USB flash drive;

Step 4: Power on the projector and insert the USB flash drive into the USB port of the projector, it will pop up a prompt "The upgrade file is detected, and the system will restart the upgrade";

Note: Power on the projector and make sure the projector recognizes the USB flash drive;

Step 5: The projector will be restarted and the upgrade process will be displayed as below;

Step 6: Please don't power off the projector during the upgrade process, the projector will automatically restart after the upgrade is completed. And then use the remote control to click on Settings>About>Software version>"U0320-V3.18" to check the software version;

Note: After the upgrade is completed, please immediately unplug the USB drive and it is recommended to delete this software installation package, otherwise it will automatically enter the upgrade mode again when booting up.

Operation Video:

If you have any questions during the process, please contact us at support@ultimea.com

Was this article helpful?

2 out of 2 found this helpful

Have more questions? Submit a request

Comments

14 comments

  • Comment author
    carlos

    How do i update de V2.14  to the V3.XX ?

    0
  • Comment author
    Ultimea

    Answer #12669

    Could you describe the problems you are currently experiencing with the device? As we have multiple suppliers of Apollo P40, there are different factory versions. V2.14 and V3. XX are just two of them.
    We can provide you with new software corresponding to the factory version if you need it.

    0
  • Comment author
    PB

    Does version 3.xx include CEC support? This functionality is urgently missing as there is no way to change the volume though e.g. the FireTV remote

    0
  • Comment author
    Andrea santambrogio

    Il mio apollo p40 ha la versione U0320-VER2.15 , è aggiornabile o no? Grazie

    0
  • Comment author
    Ultimea
    • Edited

    Answer #13495

    Hello PB,

    Our projector is only higher than the V3.09 software version that added HDMI ARC/HDMI CEC function(Such asV3.16 or V3.18), other factory versions do not support the CEC function;
    If your projector is upgraded to V3.18 or V3.16. You can try to control the projector's sound on/off & power on/off by using the FireTV remote.

    0
  • Comment author
    Ultimea

    Answer #13496

    Hello Andrea

    As we have multiple suppliers of Apollo P40, there are different factory versions. V2.15 and V3.09 are just two of them.

    If you need to download the latest version, you can refer to the corresponding new version V2.18.

    The V2.18 software version is not yet published on the website, if you need the software, please contact support@ultimea.com, and we will service you ASAP!

    0
  • Comment author
    Bartłomiej draus

    Hi my factory version is 2.17 can i update to 3.18?

     

    0
  • Comment author
    Eduardo

    Hi,
    I have the Apollo P40 Software-V2.4 version. Where can I find the download package for the next version until the latest version available (Apollo P40 Software-V3.18)?

    0
  • Comment author
    Ultimea
    • Edited

    Answer#14451

    Hello Bartłomiej,
    According to your current software version V2.17, Your software is already the latest version
    Different batches of P40 have different factory versions.V3.18 is the latest version of V3.09.
    You can also upgrade to V3.18. However, it is different from your current factory version, after downloading V3.18, there will be some differences in the UI interface and screen colors.
    We don't recommend doing that, but if you need to, you can follow the steps to upgrade to V3.18.
    Thank you!

    0
  • Comment author
    Ultimea

    Answer#14452

    Hello Eduardo,

    You can find the above article at “please download the file from the link: Apollo P40 Installation Package-V3.18...” You will be able to successfully download the V3.18 software installation package, and then follow the steps to complete the update correctly.

    0
  • Comment author
    ernesto
    • Edited

    Dear Sirs, 

    if my projector p40 has just updated the software for 3.10 version could I still upgrade to 3.18? To get it all? 

    E

    0
  • Comment author
    Ultimea

    Hello Ernesto,
    Of course, if the V3.18 version has the improvements you need, you can upgrade and experience the effects of the new version.

    0
  • Comment author
    Patryk

    Hello,

    I'm looking for a way to check how many hours P40 has run from beginning. Is there any service menu that I can access to obtain such information?

    0
  • Comment author
    Javi

    Mi proyector apollo p40 se actualizo vía ota a la versión 3.10, y veo que la última versión es la 3.18, que diferencias hay entre una y otra versión ? Debería actualizar a la versión 3.18?

    0

Please sign in to leave a comment.