Note:
① If the sound quality of the factory version meets your requirements, we do not recommend upgrading the software version
② Before upgrading this version, please make sure your factory software version is V81 or V83 or higher (Not suitable for V018/ V019 or T20/T019), if you are not sure, please contact support@ultimea.com
Improvement points:
Comparison with V109:
① Adjusted the mid-frequency
② Added BASS level: adjusted from -2~2 to -6~6, a total of 13 levels
③ Added Surround level: adjusted from -2~2 to -3~3, a total of 7 levels
④ Soundbar volume adjustment changed from 0-40 to 0-100 levels
Suggestion: Do not adjust the bass and surround sound to the highest level at the same time, as it may cause the sound to be a bit unclear.
Specific Method:
1. Copy the "update.zip" file to the USB flash drive.
Note:
① Use an empty USB flash drive, USB format: FAT32, less than 128GB;
Try to use a newer USB stick to avoid problems that cause your machine to crash.
② The file doesn't need to unzip;
2. After the Soundbar is turned on, insert the USB flash drive into the USB port, WAITING will be displayed, and then it will automatically upgrade and the progress will be displayed. Automatically standby after the upgrade is completed.
3. Press and hold the button on the right side of "surround" for 5 seconds. If the display shows "V132", it means the upgrade is successful.
- update.zip6 MB
Comments
183 comments
Buenos días ..en este momento mi equipo se encuentra en la versión V109 pero el sonido en esta versión es demasiado alto con poco volumen y me gustaría saber si actualizo a la versión V131 se podría volver a la versión V109 en casa de que no me convenciera
Hi,
I'm on firmware V109 (updated from V083) and i think it was a good update in terms of sound quality, options and sound distribution (feels like the rear speakers deliver more sound in the highest surround setting). I'm tempted to try this V131 as the annouced improvements seems very good.
Question: If anything goes wrong with firmware updates can i roll back to V083 or V109 using the same method described for updating?
Thank you to the Ultimea Team for the support and continuous improvement of your products. Cheers!
Hello Alberto & João Luís Jerónimo Pires Sardinha,
Thank you for your message.
The software for both V109 and V83 is posted on the official website.
If you are not satisfied with the new upgraded software, you can restore V109 or revert to the factory software version V83, the installation steps are the same.
Note: the USB stick only placed one version of the software.
Most importantly, we would appreciate it if you could provide us with more feelings or suggestions for the V131 software here.
Then we can better know how to improve it according to our customers' needs.
Your patience and contribution are truly appreciated!
Gracias por la respuesta
Ya sabiendo esto actualizará a la nueva versión la verdad esque la v109 está muy bien quitando el tema del sonido que es muy alto pero provea esta última a ver qué tal
Buenas noches ..he instalado la versión v 131 y todo perfecto pero final mente he vuelto ala versión v109 que es la que tenía..me sigue pareciendo mejor el sonido envolvente de esta versión para mí gusto..
Hi Alberto,
Gracias por la prueba.
¿Vemos que prefiere el v109, ¿ puede decirnos en detalle qué le gusta más del v109 o qué necesitamos mejorar en el v131?
Recopilamos activamente los comentarios de los clientes para obtener resultados de audio que satisfagan a la mayoría de los clientes lo antes posible.
¡Gracias de nuevo!
Hello everyone,
According to the feedback collected so far, Most customers prefer the subsequent new software to combine the differences between V109 and V131:
① It is suggested to keep the middle and high frequencies of V109;
② Appropriately reduce the bass of V131, so that vocal dialogue can be clearer;
③ The surround sound effect and surround sound adjustment range of V131 are better than V109, So far it's more than satisfactory;
④ The effects of EQ2 and EQ3 need to continue to improve;
Welcome more suggestions and feedback from you so that our technicians can develop a final software that meets your audio needs as much as possible.
To avoid frequent software updates, which are also more troublesome for everyone.
Thank you all very much!
Hola , os voy a decir lo que me gusta de cada versión después de las pruebas que he realizado..creo que la optimización de graves están mejor en la versión v109. Los efectos del sonido envolvente también creo que la v109 es mejor aún teniendo menos niveles de ajuste pero se aprecian mejor los sonidos envolventes o esa sensación tengo yo ..el nivel de sonido prefiero la V131 tiene un rango de ajuste más alto que la versión V109. Bajo mi punto de vista pondría los bajos y sonido envolvente de la versión v109 y el nivel de ajuste de sonido de la versión V131
Alberto
I agree with Alberto. So I propose a hybrid version that combines the best of both the V109 and V131.
1. For Bass, follow V109.
2. For surround sound, the V109 is superior. However, the V131 offers more adjustment range. So it makes sense to combine the best of both worlds. I will explain this specifically.
The "1" in V109 is stronger than the "2" in V131.
“2” in V131 is stronger than “0” in V109.
“0” in V109 is stronger than "1" in V131.
"1" in V131 is stronger than "-1" in V109.
Therefore, I propose the idea of reconstructing the surround sound effect as follows: -2(V109's -1), -1(V131's 1), 0(V109's 0), 1(V131's 2), 2(V109's 1)
3. The soundbar’s volume control range follows V131. (Maximum 100)
I have just bought the D60 and also updated the firmware to V131 but I found that the speakers are now ALOT quieter than before and need to be turned up past 35 to hear the TV!.
I might revert to V109 and see what that does???
So I have downloaded the software, put the USB into the sound bar, it says 'waiting' then shows progress up to 100, goes to standby, and the when I switch it on, it hasn't updated? I don't know what I am doing wrong, FAT32 drive 64gb. Someone help before I throw it! Currently on V83 updating to 131
I’m having the exact same issue!
Hi, first of all thank you Ultimea for the update, for me is the best about the other (anyway great surroundbar 💪🏻) for my experience i think it need more voice (trebble, middle its ok) improvement to the center speaker (better calibration between front and surround speakers). The bass are great, very good job with the subwoofer , but in my opinion it need 1 more level for less bass (-3 for example) it would be great. The no bass option in -2 its a good idea, expecially for night vision 🙂 Thanks in advance, very good job 🙂 i appreciated your work 🔝
Hello Jack & Luke,
Sorry to hear the problem.
Could you please press and hold the button on the right side of "surround" for 5 seconds? If the display shows "V131" Indicates a successful upgrade.
If "V83" is still displayed, it indicates that the upgrade has failed.
In this case, please repeat the upgrade operation.
If it still fails, please try restoring the factory settings:
https://support.ultimea.com/hc/en-us/articles/23138216963993-How-to-restore-factory-settings-
Note:
① Please format the USB memory stick before copying, please make sure the USB memory stick is empty, and keep only this one file
② USB flash drive format: FAT/FAT32; Capacity less than 128GB
If all the above methods are ineffective, please replace it with another USB stick
Could you please test it again? Thank you for your patience and understanding!
Hello davejbrogan,
Sorry for any inconvenience caused.
V131 is a temporarily tested version for everyone. After collecting everyone's opinions, we can better develop the latest version.
Regarding the issue you mentioned about the need to adjust the volume of the speaker to level 35 or above to produce sound, please refer to the improvement points in the article, as we have modified the volume adjustment range from 0 ~40 to 1~100; So you need to adjust it proportionally to the corresponding volume.
The reason for the modification is: ① Provide customers with more choices ② Some customers reported that the minimum volume was still too loud and not suitable for use at night-V83 &V109
If you don't like this improvement point, you can install the V83 factory version or V109 according to your own needs.
Thank you for your patience and support!
Important Update:
Hello, Alberto & Blue Windy & TonyC or other customers,
Based on the recently collected suggestions for V109 and V131, our technical department has developed a new version of V132 today.
Improvement points:
Comparison 131:
① Adjusted the mid-frequency a bit to make the sound clearer
② Added BASS level: adjusted from -2~2 to -6~6, a total of 13 levels
③ Added Surround level: adjusted from -2~2 to -3~3, a total of 7 levels
Suggestion: Do not adjust the bass and surround sound to the highest level at the same time, as it may cause the sound to be a bit unclear.
May I ask if it is convenient for everyone to help us conduct V132 testing again and provide feedback?
If needed, please leave a message here and I will send it to you via email.
After collecting feedback that most of the customers are satisfied with, I will publish it on the website.
We would appreciate it.
Hi Ultimea team, nice impreovements 😀yes if you want send ime the new update, i'm happy to try it and leve my feedback. Thank you to all guys for your work 💪🏻
I also want to test the V132 update. I would appreciate it if you could provide it by email. Thank you.
TonyC & Blue Windy, Thank you very much!
I have sent you the V132 software installation package via email. Could you please check it?
To prevent errors, please delete other software installation packages from the USB drive and try to use an empty USB drive.
Please feel free to contact me if you have any questions.
Hola buenos días ..a mí también me gustaría probar la nueva actualización V132 me la podrías mandar por correo
Please could I be sent V132 and see if that helps with my error? Thanks.
Gracias ..lo he recibido..lo probaré y os comento que que tal
Hi Jack,
Thank you for your message!
May I ask if you have checked the method I replied to you above?
1. Please first confirm whether the soundbar LED display version is V131
2. If not, please delete the files from the USB drive, then re-download and copy them to your USB drive for the upgrade operation again (the file name is: update.zip)
3. If method 2 fails, please restore to factory settings: https://support.ultimea.com/hc/en-us/articles/23138216963993-How-to-restore-factory-settings-
If all the above methods are ineffective, please replace one USB drive
Note: Please try to use an empty USB drive to store only one software package
V132 has also been sent to you via email, please check it.
I will follow your information. Hope to successfully solve your problem this time.
Hola, Alberto, genial.
Te he enviado un correo electrónico, por favor confirme si lo has recibido.
Muchas gracias.
Lo siento, el lenguaje de mi respuesta anterior no es correcto. Te enviaré un nuevo correo electrónico en español.
Bueno ya instalado y probado suena espectacular, me.parece que esta versión si reúne lo bueno de las anteriores versiones ..para mí gusto suena muy genial Lo único en lo que creo que se debería mirar son los modos de audio ..la verdad esque no se aprecia mucha diferencia entre los tres aún así creo que está actualización está muy bien..
Quiero daros las gracias por la atención prestada y atender nuestras peticiones para mí eso os diferencia de otras marcas..gracias y seguir asi
Hi could I please have v132 sent to my email please
Yes I tried the above and it still didn’t work. I haven’t got anything in my inbox re V132 though.
Hola he comprobado la versión y estoy en la V132..el método ha sido el que me indicasteis ..copiar archivo en pen vacía y formateada en FAT 32 encender el equipo con el HDMI desconectado poner Pen Drive en el puerto USB y empieza la carga del nuevo software ..
I have tested V132 and it is by far the best firmware version! This is a hybrid version that combines the strengths of all previous versions and is superior in all aspects. I have no further feedback to give regarding the sound, as I am satisfied with everything - sound tuning, surround effects, bass, volume control levels, etc.
If other people agree with my opinion, I think you can just post the V132 on the website and erase all previous firmware except the factory firmware.
and I feel the Ultimea development and support team to be very diligent! Thank you for all your hard work!
Hi Ultimea,
Please i'm currently on T019 and i can see that V132 has more improvements on the bass and surround levels. I would like this for my speaker. Please can i change software versions??
Please sign in to leave a comment.